Will these knuckles fit a Dana 44 IFS from late 80 through early 90's? I actually own a 93 Ranger 4x4 with Dana 35, but have read about the advantages of converting to 44 knuckles and outer stub shafts for the improved wheel bearing spacing and axle strength. I like the appearance of your product and was very curious about their interchangability with a stock Dana 44 IFS knuckle? A second question, can the top ball joint boss be milled to accept a standard Dana 35 upper balljoint.<br><br>Rob View answer
Asked 4 ´years ago | Bilstein > Reid Racing Flat Top Extreme Duty Dana 44 Knuckles | PAIR | Ford
i have a 78 bronco with a 351w out of a 72 gran torino, will this kit work on the windsor? i know the blocks are different i just don't know how different. i believe the stock pump was used when the windsor was put in. thanks View answer
Asked 2 ´years ago | Power Steering Pump | 351M 400M | 78-82 Bronco, 77-82 Ford Truck
I forgot to ask, what are the dimensions of this bag? View answer
Asked 3 ´years ago | ARB Recovery Bag
What is the length of the linkage arm between the pivot pins, and the total length of the shift lever? Also, what changes when selecting the different body lift height? Looking at this as an option for a custom truck (non-Bronco). View answer
Asked 2 ´years ago | Trail Edition Gear Banger NP435 Shifter | 66-77 Ford Bronco
How thick is the mat? View answer
Asked 4 ´months ago | Yukon Ford 9-inch Grizzly Locker | 28-spline
I have the trac bar riser for the dana 30 and it works great. problem is the axle bump stop that's there now is to short as the axle is about 6 away or so. I do not see anything about a replacement solution for this on your site. View answer
Asked 5 ´years ago | Speedometer Cable | OE-Type, 72.5-inch | 66-77 Bronco, 57-72 Ford Truck
Do these axles use the a20 style bearings? Do they come with the stock style four bolt retaining plate, or do I have to buy some kind of aftermarket u shape style? How long are the axles? From what I have seen, they should both be about 31.843 inches long. View answer
Asked 3 ´years ago | Ford 9-inch Rear Axles | 31-spline | 78-79 Ford Bronco, 73-79 F150
How do install the sleeves? I put them on the linkage and tried to pull them in by tightening, but they got stuck. Now I'm trying to put the sleeve into the knuckle first, but am having a hard time. Any tips would be greatly appreciated. View answer
Asked 2 ´years ago | TrailReady Simulated Beadlock Wheel | Select Bolt Pattern | 17x8.5
I'm looking at getting the Extreme Duty rear Driveshaft ( #8581 ) but my size isn't listed. for the custom length option do I give the tight measurement from yoke to yoke? (30 3/4 ) or do I need to subtract some, if so how much? View answer
Asked 2 ´years ago | High Clearance HD Rear Driveshaft | 66-77 Ford Bronco - Made in USA
Hi, I'm interested in the pertronix Billet Distributor. I have a 302 in a 1972 Bronco that I want to convert from points to electronic ignition. I don't know if I have a steel or cast gear but, I hear this is important. Can you provide me with the correct part number so I get the right one?<br>Thanks!<br>Scott View answer
Asked 2 ´years ago | PerTronix Billet Distributor | SBF 289 302 351W
Trying to decide on a wiring harness and saw this one. i like the severe duty part. I would like to know the physical size of the fuse panel if possible? Do yo have any feedback from anyone that has installed it in a Bronco? Can the panel be mounted in the engine compartment?<br><br>Thanks View answer
Asked 2 ´years ago | American Autowire Severe Duty Universal Wiring Harness Kit
