Question 1

Is the driveshaft black, as pictured, or natural finish? View answer

Asked 4 ´years ago | HD Rear Driveshaft | 66-77 Ford Bronco - Made in USA

Question 2

Does this MC bolt up to the Bendix booster? How tall is it? The pushrod in the booster was too long for the MC that I originally had. Found another MC but it is too tall and the hood touches the top of the MC. Had to shim the booster to angle down the MC. View answer

Asked 4 ´years ago | San Felipe Full Family Roll Bar Kit | Bare Steel | 66-77 Ford Bronco

Question 3

Is this kit made up of Distinctive Industries upholstery and foam? View answer

Asked 4 ´years ago | Parchment Seat Upholstery Set+ Foam | Front & Rear | 68-77 Ford Bronco

Question 4

Hi I have a 77 IH scout, it has a gm column non tilt. Is there an adapter available that would work with this steering wheel? View answer

Asked 3 ´years ago | Mark 7 Woody Black Billet Steering Wheel | Slotted 3-spoke | 14-inch

Question 5

What are the part numbers for the Tie rod ends? View answer

Asked 5 ´years ago | Tie Rod & Drag Link Kit | 3-way Adjustable | 66-75 Ford Bronco

Question 6

Does anybody know if this speaker will fit with Vintage Air under the dash? View answer

Asked 4 ´years ago | RetroSound In-Dash Speaker | 68-77 Ford Bronco

Question 7

Will these work in a 79 f150? <br>Thanks for helping. View answer

Asked 10 ´months ago | Wild Horses Shock, Eye/Eye, 27' Extended, 16' Compressed

Question 8

Since the Axle tubes are a smaller 3, does that mean we need to use smaller diameter U bolts when installing the leaf springs? I noticed your heavy duty Ubolt set uses 3 1/4 wide U bolts View answer

Asked 7 ´months ago | Super 9 Ford 9-inch Housing | Large Bearing | 66-77 Ford Bronco

Question 9

What is the distance between the posts? Same question for 9332? On both fenders I have a spot that has a 2 distance between two holes and I am looking for something to fit into the spot. Any recommendations are appreciated! View answer

Asked 2 ´years ago | 302 Fender Emblem + Clips | Early Style | 66-77 Ford Bronco

Question 10

Did the swap ob my 77 bronco with 2.5 lift. Was wondering what stabilizer brackets would work. Seems like the 77 brackets with shock would limit the travel of steering. I know it's not Necessary but I'd like to remove some of the twitchiness. View answer

Asked 1 ´year ago | Power Steering Conversion Kit | Quick Ratio | 66-77 Ford Bronco

Question 11

Does this come with a serpentine belt, and what is the belt part number? Thanks View answer

Asked 3 ´years ago | Power Steering Pump Bracket | 96-01 Ford Explorer 5.0L

Question 12

What is the I.D. dimension of this sleeve? Do you know if it will work with a Mustang 2 outer tie rod? Thanks in advance View answer

Asked 4 ´years ago | TrailReady Simulated Beadlock Wheel | Select Bolt Pattern | 17x8.5

Question 13

Will these work with the spicer yokes for the D20, item number 8596? View answer

Asked 2 ´years ago | Driveshaft U-bolt Kit for 1310 U-Joints | Front or Rear | 66-77 Ford Bronco

Question 14

With the fiberglass how wide are they? 4 inch? What if you have dual tanks do you have to cut the flare? View answer

Asked 2 ´years ago | Fiberglass Fender Flares | Front + Rear | 66-77 Ford Bronco

Question 15

I have the Tom's Bronco family 8 point roll cage, #1427, which has 2 diameter bars can this fit?<br>Thank you View answer

Asked 1 ´year ago | Family Cage Black Roll Bar Top Kit, 66-77 Ford Bronco

Question 16

If the front hubs are free/unlocked, does it matter which position is selected? Does the rear need to stay in the high position for normal 2WD driving? <br> Thanks! Inherited this setup with no instructions. View answer

Asked 1 ´year ago | Dana 20 Twin Stick Transfer Case Shifter Kit | Stock J-Shift | 73-77 Ford Bronco

Question 17

Do you offer a fan shroud for a 1 body lift ? View answer

Asked 2 ´years ago | Full Circle Aluminum Fan Shroud, SBF V8, 2-inch Body Lift, 66-77 Ford Bronco

Question 18

What are the extended and compressed measurements for the front and rear shocks that ship with this kit? Thanks! View answer

Asked 4 ´years ago | Early Bronco 1.5-inch Suspension Lift w/Bilstein 5100 Shocks | System 3

Question 19

Does it come with a cable? View answer

Asked 2 ´years ago | Winters Floor Shifter | Ford C6 Automatic Transmission

Question 20

Going to be ordering your Extreme duty Driveshafts for a '66 Bronco, That has the Borg Warner U-Joints. I will need to order 2 of these, correct? 1 for front & 1 for rear? View answer

Asked 2 ´years ago | Transfer Case Yoke | Dana 20, Spicer Type | 66-77 Ford Bronco

Question 21

So, the description says to use the 4 core mounts. I was looking in the questions and someone says use the 3 core and trim. Which one is it and are they in stock? Thanks View answer

Asked 2 ´years ago | Ron Davis Aluminum Radiator | Auto Trans Cooler | SBF V8 | 66-77 Ford Bronco

Question 22

I would like to use the rear family cage without any other roll bars in order to support a safari top. Will this rear cage stand alone for that purpose? View answer

Asked 6 ´years ago | Steel Tilt Steering Column | Automatic Column Shifter, 2.25-inch OD | Universal

Question 23

Two questions. First, will I need to make any modifications to this if I am running a body lift? Second, what is the thread size for the shift knob? View answer

Asked 4 ´years ago | B&M AX15 5-speed Manual Transmission Short Throw Shifter

Question 24

What size set screw is needed? These do not come with them and the ones from the original knobs are too large. View answer

Asked 1 ´year ago | Dash Instrument Knob | Flasher, Choke, Heater, Wiper | 68-77 Bronco, 68-72 Truck

Question 25

Does it come with the cable that connects to the heater control valve too? View answer

Asked 1 ´year ago | Heater Switch Cable + Bezel, Nut & Knob | 68-77 Ford Bronco

Question 26

I have a 1976 Ford F150 Ranger XLT and has a single gas ank and cap. Will this fit my truck? View answer

Asked 3 ´years ago | Metal Fuel Filler Neck | Main (Rear) Tank | 66-76 Ford Bronco

Question 27

Are the plastic glove box liners manufactured with the fuse box cutout already made? Or is the fuse box cutout made in your shop? View answer

Asked 1 ´year ago | Dakota Digital HDX Dash | Black Alloy | 66-77 Bronco, 61-66 Ford Truck

Question 28

Do you know which color wire from a factory harness should run through the voltage sensor hoop on this gauge for a 73 Bronco? View answer

Asked 11 ´months ago | Alternator Gauge | OE-Type for Stock Cluster | 66-77 Bronco, 61-66 Ford Truck

Question 29

I do not have my family cage in right now to look at, but do these mount to the top of the roll bar at the corner, and will these work under a Bimini top for the family cage? View answer

Asked 3 ´years ago | Windshield Braces | Connect to Roll Cage | 66-77 Ford Bronco

Question 30

What is the length of this column? View answer

Asked 6 ´months ago | Tilt Steering Column Kit with Automatic Column Shifter | Custom Built

Question 31

Will this work on ford 4x4 f100 ? Look like same but was not 100 % sure. Thanks View answer

Asked 6 ´years ago | Automatic Flexplate | 50 oz (Late Motor), 164 Tooth, C4 AOD 4R70W | 73-77 Bronco

Question 32

Can this mat be used in the bed of a 72 half cab? View answer

Asked 2 ´years ago | Early Bronco Steering > Bronco Sport Rubber Floor Mat | Full Rear, Black | 66-77 Ford Bronco

Question 33

Is this the correct one for an early 66 Bronco? 170 motor. View answer

Asked 1 ´year ago | 80-96 Ford Bronco & Truck Auxiliary Lights > Clutch Fork Boot | SBF 289 302 351W V8 | 66-77 Bronco, 65-79 Ford Truck

Question 34

Are replacement fan motors available if the one included fails? View answer

Asked 8 ´months ago | Aluminum Shrouded Electric Radiator Fan | High Output | 18.75 x 17.625 x 3

Question 35

Do I use the stock axle retainer plates with these axles? View answer

Asked 4 ´years ago | Ford 9-inch Rear Axles | 31-Spline, Large Bearing, 11 inch | 66-75 Ford Bronco

Question 36

Do these come with the clips to go in the door panel? View answer

Asked 3 ´years ago | Driver Front Fender Apron Brace Kit, 67-77 Ford Bronco

Question 37

Will this fit my 1966 ford Fairlane? View answer

Asked 3 ´years ago | Cowl Side Extension Panel Kit | 4-piece | 66-77 Ford Bronco

Question 38

Do you sell the pickup tube and screen separately for this kit? View answer

Asked 2 ´years ago | Engine Oil Pan Kit | Ford 351W | 66-77 Ford Bronco

Question 39

Would these rear springs work for a 79 F150 long bed? Just curious, Thanks in advance, You Guys Rock! View answer

Asked 2 ´years ago | Flex-Master Leaf Springs | 4-inch Lift | 78-96 Ford Bronco, 73-96 F150

Question 40

What hardware do I need for installing this kit? I have the spring and shackle bolt kit, the radius arm bolt kit, shackles, and nothing for the front :-) I'm working from a bare frame. Thanks!! View answer

Asked 1 ´year ago | Early Bronco 3.5 inch Suspension Lift Kit w/Bilstein Shocks | System 3

Question 41

does this skin weld on or do you bend over the edges similar to the stock door View answer

Asked 2 ´years ago | Lower Door Skin Replacement | RH Passenger | 68-77 Ford Bronco

Question 42

Will a standard volume Melling oil pump work with this pan? View answer

Asked 2 ´years ago | Engine Oil Pan Kit | Ford 351W | 66-77 Ford Bronco

Question 43

Is this sending unit for the NWMP FBR 1A tank? I cannot find the size of the tank on the WWW. View answer

Asked 10 ´months ago | Fuel Tank Sending Unit | 12-Gallon Metal Auxiliary (NWMP Style)

Question 44

Does the water pump come with a new backing plate? View answer

Asked 1 ´year ago | FlowKooler Water Pump | SBF 289 302 351W V8 | 66-77 Ford Bronco

Question 45

This is a street carburetor? Will it be okay on a Early Bronco everyday driver with mild off-roading and USFS roads? View answer

Asked 1 ´year ago | Holley Street Carburetor 2300 | 2 BBL, 500 CFM, Electric Choke

Question 46

How much lower does this tank sit compared to the stock rear 77 tank with stock body mounts? View answer

Asked 9 ´months ago | M1A1 Stainless 23-gallon Fuel Tank + Skid Plate | 66-77 Ford Bronco

Question 47

Can you confirm if this turn signal pad comes as a set, or if it is for a single pad?<br>Thank you. View answer

Asked 6 ´years ago | Black Turn Signal Body to Grille Pads | PAIR | 69-77 Ford Bronco

Question 48

are these stainless? View answer

Asked 9 ´months ago | Liftgate Striker Plate | SINGLE | 69-77 Ford Bronco

Question 49

Is this price for a pair? View answer

Asked 1 ´year ago | 80-96 Ford Bronco & Truck Body Parts > Yukon Locking Hubs | Dana 30/44, 19-spline | 66-92 Bronco, 73-93 Ford Truck

Question 50

Is this carburetor new or rebuild View answer

Asked 6 ´years ago | Holley Street Carburetor 2300 | 2 BBL, 500 CFM, Manual Choke

Browse by Topic