Question 1

Do these include a thick bearing retainer? What bearings are installed on these axles? View answer

Asked 5 ´years ago | Ford 9-inch Rear Axle Shafts | 35-spline, PAIR | 78-79 Bronco, 73-79 Ford F150 4WD

Question 2

Why does your drums have the extra holes? View answer

Asked 1 ´year ago | Dash Mounting Brackets | Stainless, PAIR | 66-77 Ford Bronco

Question 3

Since Flame Thrower II coils aren't compatible with Ignitor I systems, is it safe to assume the distributor is an Ignitor II? Also can I get the distributor with a black cap? View answer

Asked 5 ´years ago | WH PerTronix Deluxe Ignition Kit | Distributor, Coil & Plug Wires

Question 4

will these visors and new stainless rods fit with the new electric wipers ? View answer

Asked 1 ´year ago | Liftgate Striker Reinforcement | SINGLE | 69-77 Ford Bronco

Question 5

I have a sherman tank with an in tank pump and the pump is going out. can I change to a frame mounted pump. Having a brain freeze this morning. Thanks View answer

Asked 5 ´years ago | Sherman Fuel Tank EFI Pump Upgrade Kit | Convert Carb to EFI

Question 6

Please clarify - do I need a 6R80 from a 4wd truck, or does this kit adapt the tail shaft of a 2wd 6R80 to the transfer case? View answer

Asked 3 ´years ago | Dana 20 Transfer Case Adapter | Ford 6R80 4WD Automatic | Coyote Swap

Question 7

What hardware do I need for installing this kit? I have the spring and shackle bolt kit, the radius arm bolt kit, shackles, and nothing for the front :-) I'm working from a bare frame. Thanks!! View answer

Asked 1 ´year ago | Early Bronco 3.5 inch Suspension Lift Kit w/Bilstein Shocks | System 3

Question 8

Any Helpful hints on how to get the material slid in the windshield riser track? everything looks great just having trouble getting the material rope end to fit in track. Maybe just being to impatient! View answer

Asked 4 ´years ago | Family Cage Black Roll Bar Top Kit, 66-77 Ford Bronco

Question 9

does this skin weld on or do you bend over the edges similar to the stock door View answer

Asked 2 ´years ago | Lower Door Skin Replacement | RH Passenger | 68-77 Ford Bronco

Question 10

Looking to upgrade my 78 f150 400 with your saginaw conversion but I also plan on running hydro-boost and hydro-assist (eventually) so I'm looking at this pump. Can a fitting be used to cap/plug the unused return line until I need it? View answer

Asked 4 ´years ago | IDIDIT Direct Fit Tilt Column, Chrome, A/T Column Shift, 76-77 Bronco

Question 11

Will this pump sufficiently supply a FiTech go Street 400? View answer

Asked 4 ´years ago | Sherman Fuel Tank EFI Pump Upgrade Kit | Convert Carb to EFI

Question 12

Does the water pump come with a new backing plate? View answer

Asked 1 ´year ago | FlowKooler Water Pump | SBF 289 302 351W V8 | 66-77 Ford Bronco

Question 13

This is a street carburetor? Will it be okay on a Early Bronco everyday driver with mild off-roading and USFS roads? View answer

Asked 11 ´months ago | Holley Street Carburetor 2300 | 2 BBL, 500 CFM, Electric Choke

Question 14

do not see spindle bearing in the picture, will the spindle bushings fit these spindles? View answer

Asked 3 ´years ago | Front Disc Brake Conversion | Dana 30/44 | 66-75 Ford Bronco

Question 15

Are there any additional modifications recommended with the 1 lift? Like steering shaft, fuel hose, etc. Your general information on body lifts is just vague enough to make extra modifications with the 1 option unknown. View answer

Asked 3 ´years ago | Drop Pitman Arm | 78-79 Ford Bronco, 76-79 F150 4WD

Question 16

Are any parts stainless if so what parts? Do you offer a kit like this for the lift gate View answer

Asked 4 ´years ago | Tailgate Silencer Master Parts Kit | No Tailgate | 66-77 Ford Bronco

Question 17

are these stainless? View answer

Asked 7 ´months ago | Liftgate Striker Plate | SINGLE | 69-77 Ford Bronco

Question 18

Does this radiator have a cap? View answer

Asked 5 ´years ago | Tri-Pass Radiator | 3-Core, Copper/Brass, Trans Cooler | SBF V8 | 66-77 Ford Bronco

Question 19

Is this price for a pair? View answer

Asked 1 ´year ago | 80-96 Ford Bronco & Truck Body Parts > Yukon Locking Hubs | Dana 30/44, 19-spline | 66-92 Bronco, 73-93 Ford Truck

Question 20

Would these be suitable for use as a coilover mount? View answer

Asked 1 ´year ago | Turn Signal Switch | Manual or Auto | 66-73 Ford Bronco

Question 21

Does this box come with the hardware? View answer

Asked 6 ´months ago | Dakota Digital HDX Dash | Black Alloy | 66-77 Bronco, 61-66 Ford Truck

Question 22

What's the width and length of the bezel? View answer

Asked 4 ´years ago | Black Billet Dash Control Lights Bezels | PAIR | 73-77 Ford Bronco

Question 23

will this blaster heater be compatible with vintage ac iv View answer

Asked 5 ´years ago | Heater Box Assembly w/ Heat Blaster Motor Upgrade | 66-77 Ford Bronco

Question 24

What are the width and length? View answer

Asked 4 ´years ago | Black Billet Dash Control Lights Bezels | PAIR | 73-77 Ford Bronco

Question 25

What's the difference between 66-68 and 69-77? Is there a lock set for the rear door lock set that would be the same also? View answer

Asked 5 ´years ago | Door & Ignition Switch Kit | Keyed Alike | 66-77 Ford Bronco

Question 26

I have Line-ex sprayed interior, would this still fit, and would the carpet kit still fit on top of that? View answer

Asked 1 ´year ago | NP435 4-speed Transmission Gasket and Seal Kit

Question 27

I thought the ballast resistor was to protect the coil? won't the 12V to coil now burn it out? View answer

Asked 3 ´years ago | PerTronix Ignitor II Electronic Ignition | V8 | 66-77 Ford Bronco

Question 28

I'm looking to off-road, I was wondering if this shaft can handle well in sand dunning, rock crawling and muddy terrains View answer

Asked 3 ´years ago | High Clearance HD Rear Driveshaft | 66-77 Ford Bronco - Made in USA

Question 29

I am doing an engine swap with an early explorer V8. Will this radiator be a direct swap for the application as well? Thanks! View answer

Asked 4 ´years ago | Ron Davis Aluminum Radiator | Auto Trans Cooler | SBF V8 | 66-77 Ford Bronco

Question 30

Will this work with WH Ron Davis Radiator? View answer

Asked 6 ´years ago | Aluminum Shrouded Electric Radiator Fan | High Output | 18.75 x 17.625 x 3

Question 31

How does it mount ? View answer

Asked 2 ´years ago | High Performance Badge for 289 Emblem | 66-68 Ford Bronco

Question 32

How do they mount ? View answer

Asked 2 ´years ago | Fender & Grille Emblem Badge Kit | Black Chrome | 66-77 Ford Bronco

Question 33

I noticed that some of these kits were around $350. I thought that the last time i checked a couple weeks ago this set of black ones were the same price. Why isnt this set $350? View answer

Asked 3 ´years ago | Black Seat Upholstery Set + Foam Kit | Front & Rear | 68-77 Ford Bronco

Question 34

How much drop does this provide? View answer

Asked 8 ´months ago | Track Bar Drop Bracket | 78-79 Ford Bronco

Question 35

Hello, I need it to be in KM instead of Mi, can it be? Thanks View answer

Asked 7 ´months ago | Billet Instrument Cluster Bezel | 66-77 Ford Bronco

Question 36

What is the thread for the barbed fittings where they screw into the module? View answer

Asked 5 ´years ago | M1A1 Stainless 23 Gallon EFI Fuel Tank + Skid Plate | In-tank Pump | 66-77 Bronco

Question 37

Do these belts buckle into the same buckle at the retractable shoulder belts? Just wondering if I want to switch if I have to switch both parts or just the shoulder to the lap. View answer

Asked 2 ´years ago | Derale Performance > Door Latch Rod Clip | OE Metal Style, SINGLE | 66-67 Ford Bronco

Question 38

will these hinges fit a 1969 International Scout 800 or do you have a hinge that will? View answer

Asked 5 ´years ago | Quick Remove Door Hinges | Polished Stainless | 66-77 Ford Bronco

Question 39

C4 trans 4:11 gears and 35 in tires. What great do I need? View answer

Asked 4 ´years ago | Speedometer Drive Gear | 16 to 21 Tooth | 66-96 Bronco, 73-96 Ford Truck

Question 40

can this be installed with a asperated Holly carb with the idea of eventually moving to a EFI system? just trying not to have to replace the fuel pump twice? View answer

Asked 5 ´years ago | WH Frame Mounted High Pressure EFI Fuel Delivery Kit | 66-77 Ford Bronco

Question 41

Also can this be used with a 2 tank system with a manual valve? View answer

Asked 6 ´months ago | WH Frame Mounted High Pressure EFI Fuel Delivery Kit | 66-77 Ford Bronco

Question 42

How much fuel line comes with this kit? Does that give just enough to make it there or is there some extra if I decide to take the scenic route or leave a little extra line on it for an emergency repair? View answer

Asked 5 ´years ago | EFI Fuel Lines | M1A1 Fuel Tank to Throttle Body | 66-77 Ford Bronco

Question 43

I'm running the 3005netw on a 71 Bronco. scraping noise developed on drivers side when applying brakes yesterday. Pulled wheel and found that both caliper pins ( long pin with threads near hex nut that run from one side of caliper to other) were missing. Is it possible to purchase these individually? Thanks! View answer

Asked 6 ´years ago | Front Disc Brake Conversion | Dana 30/44 | 66-75 Ford Bronco

Question 44

I am in the process of putting a 1966 U13 Bronco Roadster (Budd Body) back on the road. Which product would give me a more authentic look and fit? The single piece inserts or the ones that come with the hardware kit. Thanks in advance. Peter View answer

Asked 5 ´years ago | Fiberglass Door Inserts with Backing Plates, 66-77 Ford Bronco

Question 45

Does this shock come in a straight post on top View answer

Asked 1 ´year ago | Bilstein 7100 Short Body Reservoir Shock | 360/80 | 24.25-in Extended, 14.25-in Collapsed

Question 46

Is this a low profile water pump and the water flow is regular not reverse View answer

Asked 2 ´years ago | Aluminum Water Pump | SBF 289 302 351W V8 | 66-77 Ford Bronco

Question 47

will this bracket work on 351w / thanks charlie View answer

Asked 8 ´months ago | Body Tub Bolt-on Parts + Windshield Frame | 69-77 Ford Bronco

Question 48

What Holds this bezel on? Thanks. View answer

Asked 6 ´months ago | Wiper Switch Bezel, ' Wipers' Engraved, 66-77 Ford Bronco

Question 49

Do you know if this kit will fit under 15 inch aluminum wheels? I see they should fit steel, but no mention of aluminum. Thank you. View answer

Asked 3 ´years ago | Front Disc Brake Conversion | Dana 30/44 | 66-75 Ford Bronco

Question 50

Is the price for one or two? View answer

Asked 7 ´months ago | One-Piece Door Window Kit | Vent Window Delete | PAIR | 68-77 Ford Bronco

Browse by Topic