I have a 77 and am replacing the lower quarters and at the same time removing the reserve tank. I do not want to use the filler door for the new quarter. Will this part allow me to go to the 76 and prior style filler with exposed cap? I am also installing your 23 gallon tank with EFI pump. Thanks! View answer
Asked 6 ´years ago | Metal Fuel Filler Neck | Main (Rear) Tank | 66-76 Ford Bronco
I have a 1975 Bronco. I want to upgrade the guage. My question is, Does the speedometer require the use of the factory speedo cable from the output shaft on the transfer case or elsewhere? I want to eliminate the speedo cable. View answer
Asked 5 ´years ago | Dakota Digital VHX Dash | Black Alloy & White | 66-77 Bronco, 61-66 Ford Truck
I want to install the hyperspark ignition on my engine but my camshaft requires a steel gear or melonized iron gear on the distributor. If I purchase the Hyperspark distributor from you, can you replace the cast gear with the appropriate gear for an additional fee? View answer
Asked 6 ´years ago | Holley Sniper EFI Hyperspark Distributor | Ford 289 302 | 565-301
I purchased and installed this setup a few years back.. What size ball-joint (O.D.) does this setup have where the tie-rod connects to the drag-link? Looking to order one of those bushing called the cure to eliminate the dead-band in the steering. There are (2) sizes... 3/4 or 5/8 View answer
Asked 5 ´years ago | Power Steering Conversion Kit | Quick Ratio | 66-77 Ford Bronco
what is this used for? View answer
Asked 1 ´year ago | GPS External Antenna for Dakota Digital GPS-50-2
Do you have an installation guide for this? I'm curious about taking apart the assembly and if it's just nuts that you need to take off and move each individual gauge over to the new speedo panel. or if there are rivets to drill out or anything like that? View answer
Asked 5 ´years ago | Speedometer Gauge - 'Unleaded Gasoline Only', 66-77 Ford Bronco
I purchased a full front and rear disc brake kit from you for my 1974 bronco, will these knuckles work with that kit? And also is the opening large enough to allow me to remove your heavy duty front chromoly shafts with gold joints without removing the knuckle? View answer
Asked 3 ´years ago | Reid Racing Flat Top Dana 44 Knuckle | LH Driver, 6-Bolt | Chevy
Do you sell the mount for the can? View answer
Asked 6 ´years ago | Fuel Jerry Can w/Spout | Black | 5-Gallon (20L)
I recently installed a Holley Sniper and am wondering if this Gas Cap will be vented well enough so that I do not have to have a secondary vent coming off the tank itself. I currently have a secondary vent line off the tank running up into my rear bed pillar, the only issue is when doing harder trails I get a lot of slosh and spillage out of this vent line. Hoping to eliminate the smell and the waste of fuel. Thanks View answer
Asked 11 ´months ago | Vented Gas Cap | OE-Type, Paintable, 3.25-in OD | 71-76 Bronco, 73-76 Ford Truck
Hello, With the added thickness of the Racket jacket along with the thickness of the carpet, how's does it affect the carpet hold down pieces along the edge of the doors? Do the strips arch between the hold down screws? Thanks View answer
Asked 5 ´years ago | NP435 4-speed Transmission Gasket and Seal Kit
Hi. I have a stock 1976 Bronco with a V8. I would like to purchase the Super Mega kit (#5586NET). I have never taken on such a big job. Does the kit include instructions or a diagram to complete the assembly? View answer
Asked 1 ´year ago | SUPER MEGA Early Bronco Body Tub Kit w/Flared Quarters & Bolt-On Parts
I put 1.5 leveling springs on my 73 , feels like the stock shocks just don't work .I go over a bump it rides really rough . I know I had to compress my spring to get shocks back on so I know I have a problem ,which shocks should I get for a smoother ride. View answer
Asked 5 ´years ago | WILD HORSES Shock, Stud/Eye, 19' Extended, 12' Collapsed
