Question 1

Are these satin or gloss and are the open ones for the front satin or gloss? View answer

Asked 9 ´months ago | Black Rear Wheel Center Cap | Closed | 4.25 inch Diameter

Question 2

What gauge or thickness is this bumper made of? View answer

Asked 1 ´year ago | Super Stock Bumper | Black E-Coat, Front or Rear | 66-77 Ford Bronco

Question 3

Ive had my custom steering shaft installed fir a few year and love it. The one thing about it I'm not sure if its right or not. The shaft is completely compressed together when installed, which leaves no room for compression in the event of a front end collision. Should I shorten the sleeved upper segment? If so how much? View answer

Asked 4 ´years ago | Collapsible Lower Steering Shaft | Custom Built | 66-77 Ford Bronco

Question 4

How many lumens are each of these lights rated in low and high beam settings? View answer

Asked 3 ´months ago | JW Speaker Black LED Headlights | 8700 Evolution 2 | 66-78 Bronco, 48-78 Ford Truck

Question 5

How dose this differ from the door skin? Item #: 5780 vs. Item #: 5689? Thanks. View answer

Asked 4 ´years ago | Lower Door Shell | RH Passenger | 66-67 Ford Bronco

Question 6

Can you get 1 piece quarter panels with the tub assembly View answer

Asked 5 ´years ago | Early Bronco Body Tub Kit w/Uncut Quarters | Freight Included

Question 7

Does the custom crossmember bolt to the factory location? View answer

Asked 4 ´years ago | AX15 Transmission Deluxe Kit (w/New Trans), T-Shift Dana 20, 66-72 Bronco

Question 8

I will be installing the WH 1.5 suspension lift along with a 1 body lift. The transmission is an AX15. Which will be a better fit? The shorty or the long tub headers? Thank you. View answer

Asked 2 ´years ago | Small Block Ford Shorty Headers w/O2 | Ceramic | SBF 289 302 5.0L V8

Question 9

Can this be attached to frame for safety? View answer

Asked 4 ´years ago | Steel Tilt Steering Column | Automatic Column Shifter, 2.25-inch OD | Universal

Question 10

Does the v-belt pulley have the fan with it as the original Alt? View answer

Asked 3 ´years ago | 3G Alternator | One-Wire, High Output, 90/130 Amp | 66-77 Ford Bronco

Question 11

whats the size of this grommet? View answer

Asked 5 ´years ago | Tailgate License Plate Light Wire Grommet | SINGLE | 66-77 Ford Bronco

Question 12

what is this used for? View answer

Asked 1 ´year ago | GPS External Antenna for Dakota Digital GPS-50-2

Question 13

Do you have an installation guide for this? I'm curious about taking apart the assembly and if it's just nuts that you need to take off and move each individual gauge over to the new speedo panel. or if there are rivets to drill out or anything like that? View answer

Asked 4 ´years ago | Speedometer Gauge - 'Unleaded Gasoline Only', 66-77 Ford Bronco

Question 14

Hey, will this hood still allow my windshield to fold down and lay flush on the hood? Or does it stick up too high? Want to place an order for this asap! Thanks View answer

Asked 2 ´years ago | Corbeau Seats > Highlander Fiberglass Hood | Deluxe | 66-77 Ford Bronco

Question 15

can the dual return HD pump be substituted for difference between pump price? View answer

Asked 2 ´years ago | Custom Rocker Switch Panel | 6 Switches | Brushed Stainless

Question 16

Can these mounts be used to replace the stock rear mounts? View answer

Asked 10 ´months ago | Walnut Steering Wheel Horn Bar | 74-77 Bronco, 71-77 Ford Truck

Question 17

I just stumbled across this Gear Banger kit. I have a 1978 Jeep CJ5 that the previous owner did a NP435 conversion in. I love the transmission, but hate the long throw of its shifter. Plus in granny or third gear the shifter is practically shoved to the dash. Would this application work for my CJ? Thanks, Danny View answer

Asked 11 ´months ago | Trail Edition Gear Banger NP435 Shifter | Complete Kit | 66-77 Ford Bronco

Question 18

do you need to apply silicone on the seals of the electric washer pump? View answer

Asked 2 ´years ago | Windshield Washer Solvent Reservoir Motor | 71-96 Ford Bronco & Truck

Question 19

Does the body kit come with a fully welded floor pan or just the parts to weld myself? View answer

Asked 3 ´years ago | Early Bronco Body Tub Kit w/Uncut Quarters | Freight Included

Question 20

How do you remove the old T-Handle? View answer

Asked 3 ´years ago | Dana 20 Transfer Case Shifter T-Handle | 66-72 Ford Bronco

Question 21

Are the rear panels drilled out for the cap mounting bolts? View answer

Asked 2 ´years ago | Early Bronco Body Tub Kit w/Uncut Quarters | Freight Included

Question 22

Is it possible to purchase the grille and tailgate and include them in the "Free Shipping" kit? ready to pull the trigger. View answer

Asked 3 ´years ago | Early Bronco Body Tub Kit w/Uncut Quarters | Freight Included

Question 23

Do you have a complete Early Bronco Kit that also includes the Bronco Tub Kit & the doors and door frames, windshield frame, fenders, grille, tailgate, hood and top? I'm considering a build soon. View answer

Asked 3 ´years ago | Early Bronco Body Tub Kit w/Uncut Quarters | Freight Included

Question 24

I'm rebuilding my 1967 Bronco brake set up and have lost my stock distribution block. Will this disk/disk proportioning valve do the trick? If so what additional fittings (if any) will i need? I have a all drum set up. Thanks View answer

Asked 2 ´years ago | Proportioning Valve, 66-77 Ford Bronco

Question 25

where are your tub parts made? View answer

Asked 5 ´years ago | Early Bronco Body Tub Kit w/Uncut Quarters | Freight Included

Question 26

Does this include heater seal kit? View answer

Asked 6 ´years ago | Heater Box Assembly w/ Heat Blaster Motor Upgrade | 66-77 Ford Bronco

Question 27

I recently purchased this housing. I will be building it for my bronco. I definitely use my rig, but I dont abuse it. Do you see any need to truss this housing? I will be running a Tru hi9 center section with 4.88 gears and a yukon grizzly locker with your 35 spline axles. I plan on running 37 inch tires. View answer

Asked 4 ´years ago | Super 9 Ford 9-inch Housing | Large Bearing | 66-77 Ford Bronco

Question 28

Does this Super 9 Housing take the same Axles and Brakes as the Original 1977 Bronco housing? View answer

Asked 1 ´year ago | Super 9 Ford 9-inch Housing | Large Bearing | 66-77 Ford Bronco

Question 29

Does this radiator need wider mount or will the stock mounts work? I see it doesn't have the trans cooler, so which aftermarket trans cooler would you suggest? Thanks Dave View answer

Asked 4 ´years ago

Question 30

Is this housing American made? Do you feel it is stronger than the '76/'77 housing? View answer

Asked 3 ´years ago | Super 9 Ford 9-inch Housing | Large Bearing | 66-77 Ford Bronco

Question 31

Do you have the specifications for the amp draw with this new starter ? View answer

Asked 9 ´months ago | Hi Torque Gear Reduction Starter | SBF 289 302 351W V8 | 66-77 Ford Bronco

Question 32

Since there are so many similarities, will this fit a 1979 F150 Tailgate? View answer

Asked 4 ´years ago | Locking Tailgate Release Handle | SS | 66-77 Bronco, 64-72 Ford Truck

Question 33

Can I use this setup w a Coyote motor? View answer

Asked 1 ´year ago | WH Frame Mounted High Pressure EFI Fuel Delivery Kit | 66-77 Ford Bronco

Question 34

Is there a benefit of getting the billet BL vs the urethane mounts? View answer

Asked 3 ´years ago | Holley Sniper EFI Hyperspark Distributor | Ford 289 302 | 565-301

Question 35

will this work with 5.0 motor View answer

Asked 2 ´years ago | Black Alternator Brackets | SBF 289 302 351W V8 | 66-77 Ford Bronco

Question 36

Will these work with changing back and forth from hard top to Rampage soft top? View answer

Asked 4 ´years ago | FAST TOP Hard Top Mount Kit | 66-77 Ford Bronco

Question 37

I forgot to ask, what are the dimensions of this bag? View answer

Asked 3 ´years ago | ARB Recovery Bag

Question 38

Does this bag have rings or anything on the bottom to secure it to the truck? View answer

Asked 4 ´years ago | ARB Recovery Bag

Question 39

My running length measurement is 34 inches do I go with the 34.5 or the 33.5 View answer

Asked 2 ´years ago | HD Rear Driveshaft | 66-77 Ford Bronco - Made in USA

Question 40

Where are the rubber bushings for the adjustable draglink to tie rod side for non clydesdale? Is this it also? View answer

Asked 3 ´years ago | Dana 44 Inner Axle | 4340 Chromoly, LH Driver | 78-79 Bronco, 68-79 F150

Question 41

I'm doing a frame-off restomod on my 77 and have leaking factory gear box and pump. Would this be a good option to refresh the factory system? I also bought a tilt-column from you along with 1 body lift and 2.5 suspension lift. Thanks! View answer

Asked 1 ´year ago | Power Steering Conversion Kit | Quick Ratio | 66-77 Ford Bronco

Question 42

Can you get these in parchment color? (So I can dye them to match my seats?) View answer

Asked 4 ´years ago | Door Side Mirror | Chrome, Convex Glass | 1967 Ford Bronco

Question 43

Is the shift knob the same thread pattern as the factory ford np435 shift knob? View answer

Asked 4 ´years ago | Trail Edition Gear Banger NP435 Shifter | Complete Kit | 66-77 Ford Bronco

Question 44

Does this (5045 Overflow Bottle with Stainless Hardware) come with the hose like the OEM version does. If not what is the part number for the hose. View answer

Asked 5 ´years ago | Radiator Overflow Tank | Stainless Brackets | 66-77 Ford Bronco

Question 45

My Bronco has an aftermarket power steering box put on by the previous owner. It does not look like a Ford steering box and the pump looks like the GM ham can pump. Would this arm fit the aftermarket conversion steering box? View answer

Asked 5 ´years ago | Drop Pitman Arm | 67-75 Ford Bronco

Question 46

I need the rubber seal that covers the ball joint at the drag link end that attaches to the pitman arm. Could you please give me the part number? Thank you. View answer

Asked 3 ´years ago | Dana 44 Inner Axle | 4340 Chromoly, LH Driver | 78-79 Bronco, 68-79 F150

Question 47

Do these axles use the a20 style bearings? Do they come with the stock style four bolt retaining plate, or do I have to buy some kind of aftermarket u shape style? How long are the axles? From what I have seen, they should both be about 31.843 inches long. View answer

Asked 3 ´years ago | Ford 9-inch Rear Axles | 31-spline | 78-79 Ford Bronco, 73-79 F150

Question 48

Can I install this without removing the transfer case? I have a 1975, 302 w/auto. View answer

Asked 3 ´years ago | Dana 20 Twin Stick Transfer Case Shifter Kit | Stock J-Shift | 73-77 Ford Bronco

Question 49

Can I purchase the antenna without the bezel and nut? My Bezel is in good shape. View answer

Asked 3 ´years ago | Radio Antenna Assembly | OE-Type | 66-77 Ford Bronco

Question 50

how to install View answer

Asked 3 ´years ago | Lower Windshield Frame Hinge Seal | 66-77 Ford Bronco

Browse by Topic