Question 1

Does this synchronize 2 motor setups? View answer

Answer posted 3 years ago | Intermittent Wiper Switch + Delay Module | 69-77 Bronco, 67-72 Ford Truck

Question 2

Where is the drain plug located? Is it on bottom of pan? My 69 bronco has it on the back of the pan.. thanks View answer

Answer posted 3 years ago | Engine Oil Pan Kit + Stainless Dip Stick & Tube | SBF 289 302 V8 | 66-77 Ford Bronco

Question 3

Does this have the mounting plate on this column, or do we need to buy your mount? No mounts in pic, just confirming... View answer

Answer posted 3 years ago | Tilt Steering Column Kit for Floor Shifter | Custom Built

Question 4

Being a vertically challenged guy....will the overall height of the hood in the open position be the same height or lower? Love the idea but don't want my hood any higher than what it is already. View answer

Answer posted 3 years ago | Shox N The Hood | Black Hydraulic Hood Props | 66-77 Ford Bronco

Question 5

will this fit a 1996 f150? View answer

Answer posted 3 years ago | Full Size WH Winch Bumper (Unwelded Kit), 87-96 Ford Bronco & F150

Question 6

will this fit around an IDIDIT tilt steering column? View answer

Answer posted 3 years ago | WH Billet Gauge Cluster and Column Bezel Black, 66-77 Ford Bronco

Question 7

What brand is the brake pads? View answer

Answer posted 3 years ago | Front Disc Brake Conversion Kit | Dana 30 & Dana 44 | 66-75 Ford Bronco

Question 8

Do you sell the gas cap that these covers go on? If so what is the part number? View answer

Answer posted 3 years ago | Black Billet 'Grabber' Fuel Cap Cover | for Non-Locking 2.80 inch OD Cap

Question 9

Are these cut to length to fit 289,and do they come in blue? Thanks View answer

Answer posted 3 years ago | MSD 8.5mm Super Conductor Spark Plug Wires Set | Black | 31193

Question 10

I have a 1969 and am getting ready to install an AOD in place of a 3spd column shift. I would like to keep the stock steering wheel. Can this column be used on a '69? If so, what will have to be modified? View answer

Answer posted 3 years ago | IDIDIT Direct Fit Tilt Column, Black, A/T Column Shift, 76-77 Bronco

Question 11

Is the white like a parchment white or just straight white? View answer

Answer posted 3 years ago | Billet Aluminum 1 inch Body Lift Blocks | Set of 8 | 66-77 Ford Bronco

Question 12

Will these clean better than my stock Sasquatch fender flares?. Mud seems to stain them. Are these a smooth finish? View answer

Answer posted 3 years ago | Air Design Wide Fender Flares, 4-Door, 21-24 Ford Bronco - VM2DZ-16268-A - FO34E11

Question 13

The heater control knobs don't seem to come off. Can these knobs be made to fit those? View answer

Answer posted 3 years ago | Billet Dash Knob | OE Look, Each | 66-77 Bronco, 61-72 Ford Truck

Question 14

Could you order a 1410 non cv flange for this unit and how much. View answer

Answer posted 3 years ago | Extreme Duty Dana 20 Output System | 1350 Flange | with Speedometer Parts

Question 15

Can this be order in 17x12 or 17x14 width? View answer

Answer posted 3 years ago | TrailReady Beadlock Wheel | HD Series - Cast Aluminum | 17x8.5

Question 16

My grille has 10 holes, Kit comes with (13) clips, and (3) of the clips have a nut set into the clip. The other (10) clips are just circles. Where do the (3) odd-ball clips with nuts go on the grille? Thank you. View answer

Answer posted 3 years ago | Grille Bolts & Clips | 26 piece Set | 66-77 Ford Bronco

Question 17

Are these chrome? The picture makes it look like its brass. View answer

Answer posted 3 years ago | Vent Window Handle Bracket | LH Driver | 68-77 Ford Bronco

Question 18

Do you make this bumper to accomodate a EB with body lifts? View answer

Answer posted 3 years ago | Bailie Bilt Front Modular Winch Bumper | 66-77 Ford Bronco

Question 19

Is this the standard rotation pump for v-belt setups? View answer

Answer posted 3 years ago | FlowKooler Water Pump | SBF 289 302 351W V8 | 66-77 Ford Bronco

Question 20

Is this a two part cover, so it will fit after column is installed? View answer

Answer posted 3 years ago | High Tech Throttle Spring Kit, Holley 4-Barrel

Question 21

Do I need to use the skid plate with this tank View answer

Answer posted 3 years ago | Rear Main Fuel Tank Master Kit | OE Type | 66-76 Ford Bronco

Question 22

Will this roll bar work on a 1986 k5 full size blazer, thx Jerry View answer

Answer posted 3 years ago | Chrome Tilt Steering Column | Automatic Column Shifter, 2.25 inch OD | Universal

Question 23

Are these a Satin black? want to make sure they are not Black Chrome. Thank you! View answer

Answer posted 3 years ago | Bronco Script Fender Emblem | Black | 66-77 Ford Bronco

Question 24

Are the hinges stainless steel? View answer

Answer posted 3 years ago | Hard Top Liftgate with Hinges | 70-77 Ford Bronco

Question 25

Are there any other options for a syncro switch? I hate to put a hole in my new dash. View answer

Answer posted 3 years ago | Synchronizing Windshield Wiper Switch with Intermittent Delay

Question 26

Hi, I can't find the specs. Would it be possible to send? Mostly interested in the width and height (assembled). Also the angled pieces that mount back by the rear fenders ... what is the distance from the main hoop? Thanks! View answer

Answer posted 3 years ago | Chrome Tilt Steering Column | Automatic Column Shifter, 2.25 inch OD | Universal

Question 27

I have disc on the front and drums on the back, is this unit for my brake system? View answer

Answer posted 3 years ago | Power Brake Kit, Chrome Booster & Burnished Wilwood Master Cylinder, 67-77 Ford Bronco

Question 28

Just installed my atlas and to make sure this speedometer cable is the one I need to work with the stock Bronco Speedometer head? View answer

Answer posted 3 years ago | Speedometer Cable for Atlas or HD Dana 20 Output

Question 29

Are these panesl rigid enough to mount speakers on them? View answer

Answer posted 3 years ago | MSD Black Pro-Billet Distributor | SBF Ford 289 302 V8 | 85793

Question 30

Is this for just one hose or does it include two hoses (one for each side)? View answer

Answer posted 3 years ago | Billet Aluminum Dual Hose Separator Clamp | 1/2 inch ID

Question 31

Have a 76 with Full width reverse Dana 44. Will this kit work? Do you have options for my setup? Thanks. View answer

Answer posted 3 years ago | Dana 20 Transfer Case Adapter | Ford C6 Automatic | 66-77 Ford Bronco

Question 32

Will the NV3550 conversion match up to a 200 CID 6 cylinder? View answer

Answer posted 3 years ago | Deluxe NV3550 Transmission Adapter Kit | No Trans | 66-77 Ford Bronco

Question 33

does unwelded mean it needs to be completely assembled or just weld the winch plate in and paint it? View answer

Answer posted 3 years ago | Full Size WH Winch Bumper (Unwelded Kit), 87-96 Ford Bronco & F150

Question 34

Does this kit come with wire loom to wrap the wire in? View answer

Answer posted 3 years ago | WH Deluxe Rewire Kit with American Autowire Harness | 66-77 Ford Bronco

Question 35

I have a 1995 5.8 L in a 1966 Bronco with a new 3 row radiator for a 5.0 swap ! Will this hose work on my application? View answer

Answer posted 3 years ago | Lower Radiator Hose | Mustang or Explorer 5.0L Swap | 66-77 Ford Bronco

Question 36

Does it come with the heat protector sleeves ? If not, do you sell them , what is the part number for them if so. View answer

Answer posted 3 years ago | Machined Aluminum Plug Wire Divider | Satin | SBF Ford 289 302 351W

Question 37

Can you use this with EFI? View answer

Answer posted 3 years ago | Electric Fuel Tank Selector Valve | Carbureted | 66-86 Bronco, 67-87 Ford Truck

Question 38

runs on batteries ? View answer

Answer posted 3 years ago | Locking Tailgate Release Handle | SS | 66-77 Bronco, 64-72 Ford Truck

Question 39

What sort of modifications to these need to be used on a 77 I'm assuming some trimming for the gas filler but just wondering how much View answer

Answer posted 3 years ago | Upper & Inner Quarter Panel | Stamped, LH Driver | 66-76 Ford Bronco

Question 40

I have a inline 6/200 that the alternator went out. I am planning to replace it and was wondering if I had plans to eventually do a v8 swap, would this alternator work? View answer

Answer posted 3 years ago | 3G Alternator | One Wire, High Output, 90/130 Amp | 66-79 Bronco, 65-79 Ford Truck

Question 41

Do you have a replacement dipstick for this? The handle broke off of the dipstick. Was probably tweaked when we were loading the engine - not a manufacturing issue. Thanks View answer

Answer posted 3 years ago | Engine Oil Pan Kit | Ford 351W | 66-77 Ford Bronco

Question 42

This will replace my original drag link on my 1969 Bronco that is to long for my F-100 power steering box, Right? View answer

Answer posted 3 years ago | Rear Leaf Spring Bushings | Urethane | 66-77 Ford Bronco

Question 43

does this skin weld on or do you bend over the edges similar to the stock door View answer

Answer posted 3 years ago | Lower Door Skin Replacement | RH Passenger | 68-77 Ford Bronco

Question 44

I have a 2022 Bronco Badlands non-sasquach. I understand that there are different bushings for the HOSS 3.0 suspension. Is that correct and if so, how do I make sure I get the right one? View answer

Answer posted 3 years ago | BroncBuster Tie Rod Brace + Rack Bushing Upgrade Kit | 2021+ Ford Bronco

Question 45

purchased adjustable drag link, I have WH steering box that mounts inside of frame, rod end that attaches to pitman arm is too long, need one that measures 6.5 to 7, can you help. Thanks View answer

Answer posted 3 years ago | Quick Remove Door Hinges | Door Side Only, Stainless | 66-77 Ford Bronco

Question 46

I have a 1968 F100 4x4 front Dana 44, but the knuckles are the same as the Bronco Dana 30. Will this kit work for my application? View answer

Answer posted 3 years ago | Front Disc Brake Conversion Kit | Dana 30 & Dana 44 | 66-75 Ford Bronco

Question 47

Is the sending unit that comes with item #9690 compatible with the VHX you have and which setting Thanks Dan View answer

Answer posted 3 years ago | Rear Main Fuel Tank Master Kit | OE Type | 66-76 Ford Bronco

Question 48

I have a 67 truck with 76 axle, what bushings are diffirent in 75-76 kit and which one should I get? View answer

Answer posted 3 years ago | Tailgate Upper & Lower Bumpers | 4 piece | 66-77 Bronco, 61-72 Ford Truck

Question 49

what kind of mounting hole I need to cut in my dash! I have no radio . View answer

Answer posted 3 years ago | RetroSound Huntington Direct Fit Radio | AM/FM, Bluetooth | 66-77 Bronco, 61-66 Ford Truck

Question 50

Does the tuffy security box come as one piece insert into the glove box area or do I have to use my original glove box interior. Thanks View answer

Answer posted 3 years ago | AX15 Kit with Brand New Transmission For 66-72 Bronco T-Shift Dana 20

Browse by Topic