Are the headrests removable? View answer
Answer posted 2 years ago | Ford 6R80 Crossmember Kit | 66-77 Ford Bronco Coyote Swap
I'm assuming these replace the two under hood bumpers. so that means that I'd need to drill a hole through the hood the size of the under post of the poly part? does anyone know what size that is or have any recs on how to do that? View answer
Answer posted 2 years ago | Dakota Digital > Urethane Hood Pins | PAIR | Various Color Options
I was wondering if there is any though to making a kit so I could have quick disconnect for my stock doors and put a set on your rock doors? Right now the kit would only work for one set of doors and I do not need the whole kit for the second set. View answer
Answer posted 2 years ago | Quick Remove Door Hinges | Polished Stainless | 66-77 Ford Bronco
Can you use gorilla locking lug nuts on the 17x9 wheels? View answer
Answer posted 2 years ago | US Mags Indy Wheel | 17x9 | 5x5.5 Bolt Pattern
Is # 6502 an electric antenna View answer
Answer posted 2 years ago | Radio Antenna Assembly | OE-Type | 66-77 Ford Bronco
I have a set of extended radius arms that are 10.5 inches longer than stock. They have 5 degrees built in. They are coupled with your system 7, 3.5 inch lift with hoops. Will I be ok with 4 degree c-bushings? Thanks. View answer
Answer posted 2 years ago | Side Marker Light Lens Gasket | 70-77 Bronco, 70-72 Ford Truck
What vehicle will seat cover fit View answer
Answer posted 2 years ago | Door Hinge Shim | Stainless, 1/32-inch Thick | 66-77 Ford Bronco
how many positions tilt does this have ? View answer
Answer posted 2 years ago | IDIDIT Direct Fit Tilt Column, Chrome, Floor Shift, 76-77 Bronco
77 Bronco with Sniper master kit, new Painless wire harness. What additional modules do I need to make this guage fully functional and accurate. Also have the 23 gallon tank with in-tank pump from WH. Thanks View answer
Answer posted 2 years ago | Dakota Digital VHX Dash | Black Alloy & Blue | 66-77 Bronco, 61-66 Ford Truck
Does the rear tumble seat come in parchment color? View answer
Answer posted 2 years ago | Ford 6R80 Crossmember Kit | 66-77 Ford Bronco Coyote Swap
Hi, I'm interested in the pertronix Billet Distributor. I have a 302 in a 1972 Bronco that I want to convert from points to electronic ignition. I don't know if I have a steel or cast gear but, I hear this is important. Can you provide me with the correct part number so I get the right one?<br>Thanks!<br>Scott View answer
Answer posted 2 years ago | PerTronix Billet Distributor | SBF 289 302 351W
What is the on center dimension of the outer bump stop mounting studs? View answer
Answer posted 2 years ago | Dash Key Protector | 66-77 Ford Bronco
Is it a complete set? For both sides? View answer
Answer posted 2 years ago | Stage 8 Locking Header Collector Bolts | 3/8-16, Set of 6
I have an 85 302 sbf manual trans with a 68 bronco bell housing bolts are 5.25 center to center for starter . I'm thinking this should work ? Can you check specs for bolt pattern please . Going into bronco with ax15 View answer
Answer posted 2 years ago | Hi Torque Gear Reduction Starter | SBF 289 302 351W V8 | 66-77 Ford Bronco
Do you have a 1.5 - 2 leveling block for the front end coil springs to take the rake out? I also have a clearance problem with my 33 tires rubbing on the front edge of the fenders when turning. I already trimmed a little off the fenders and can trim a little more but I was wondering if you had a leveling block. View answer
Answer posted 2 years ago | Racket Jacket Wheel Well Insulation Kit, 66-77 Bronco
