Does this come with lugs? View answer
Answer posted 6 years ago | US Mags Indy Wheel | 15x8 | 5x5.5 Bolt Pattern | 66-79 Bronco, 64-79 F150
What are these made of? Ceramic? Semi-metallic? View answer
Answer posted 6 years ago | Disc Brake Caliper Pads for WH Front Disc Conversion
Got these headlights and they were quick to hook up, but the halo isn't working with the turn signal, as in it's not blinking orange. Is that what it's supposed to do? If so, what is or isn't hooked up correctly? View answer
Answer posted 6 years ago | Revolution LED Headlights | Chrome with Halo, 7 inch Round | 66-78 Bronco, 48-78 Ford Truck
I purchased these lights about a year ago. I recently installed a 75amp alternator. My headlamps quit working. I have power going to both of the fuses in the harness that came with the headlamp kit but no power going out. Looks like both fuses blew. Can I get some ne ones? Could this be an issue with the new alternator of just bad timing?<br>SG View answer
Answer posted 6 years ago | H4 Headlight Conversion Kit w/Night Lighter Harness, 66-77 Ford Bronco
Does this console cover up the inner seatbelt holes? View answer
Answer posted 6 years ago | Double USB Charger Outlet with Voltmeter | Red Indicator
dose the colnum come in black View answer
Answer posted 6 years ago | Tilt Steering Column Kit for Floor Shifter | Custom Built
I'm doing the install on the 6129 harness. I am trying to figure out the wire connections for the yellow connector (white red and black wires). I don't have the female connector in the spaghetti of what the prior owner left me in the vehicle). The ground is pretty straight forward but not sure about the other two wires? <br>Thanks! View answer
Answer posted 6 years ago | Night Lighter Headlight Harness | Extreme Duty | 66-79 Ford Bronco
WAS WANDERING WHICH DIRECTION DOES THE KICKPANEL INSERT GO. LONG END WITH LIP TOWARDS HEATER BOX OR SHORT END TOWARDS HEATER BOX? WAS THINKING SHORT END TOWARDS BOX AND LONG END TOWARDS FENDER TO PREVENT WATER FROM COMING THRU? THANKS IN ADVANCE! View answer
Answer posted 6 years ago | Heater Air Inlet Duct | 66-77 Ford Bronco
I have a 1976 Bronco with a 351W and an AOD trans ! Will there be any problems with the fit. I already bought a pair of long tubes and they said they would fit but right side is against the trans oil pan and left side is tight against the frame ! View answer
Answer posted 6 years ago | Pro Flow Ceramic Headers | SBF 289 302 351W V8 | 66-77 Ford Bronco
Are the headrests removable? View answer
Answer posted 6 years ago | Ford 6R80 Crossmember Kit | 66-77 Ford Bronco Coyote Swap
What size is your ford logo round emblem? View answer
Answer posted 6 years ago | Ford Oval Logo Round Sticker Decal, 1-3/8 inch
I want to install the hyperspark ignition on my engine but my camshaft requires a steel gear or melonized iron gear on the distributor. If I purchase the Hyperspark distributor from you, can you replace the cast gear with the appropriate gear for an additional fee? View answer
Answer posted 6 years ago | Holley Sniper EFI Hyperspark Distributor | Ford 289 302 | 565-301
I have no wires in the frame now. The kit comes with short wires on the switch. Do I just pull the 8 or so wires shown on the instructions up through the frame on the drivers side and run to the motors? View answer
Answer posted 6 years ago | Synchronized Electric Windshield Wiper Kit | Dual Motor | 66-77 Ford Bronco
