Question 1

Do these axles use the a20 style bearings? Do they come with the stock style four bolt retaining plate, or do I have to buy some kind of aftermarket u shape style? How long are the axles? From what I have seen, they should both be about 31.843 inches long. View answer

Answer posted 3 years ago | Ford 9-inch Rear Axles | 31-spline | 78-79 Ford Bronco, 73-79 F150

Question 2

Can the radiator be built with reversed inlet and outlet connections? I have a 351w with the explorer front serptine setup. View answer

Answer posted 3 years ago

Question 3

Does the dash come with glove box and cigarette tray? View answer

Answer posted 3 years ago | Steel Dash Panel | OE-Type | 73-77 Ford Bronco

Question 4

I looking at adding the Clydesdale steering to my 79 Bronco. Planning on running 17 wheels. Not sure what backspacing/offset on the wheels would be needed. Do you have any recommendations? Thanks! View answer

Answer posted 3 years ago | CLYDESDALE Steering Tie Rod & Drag Link Set | 78-79 Ford Bronco, 76-79 F150 4WD

Question 5

Are these cut by year? For example I have a 1967 and the rear seat has very small tight armrests and I dont see that on this set. Does this come with matching armrest covers as well per year? View answer

Answer posted 3 years ago | Billet Aluminum 1-inch Body Lift Blocks | Set of 8 | 66-77 Ford Bronco

Question 6

Will the pertronix flame thrower III units work in my 79 ford 460? It says for early ford to 1977. View answer

Answer posted 3 years ago | PerTronix Flame-Thrower III Ignition Coil | Chrome

Question 7

Will this bearing fit on the 31 spline Axle shaft? View answer

Answer posted 3 years ago | Small Rear Axle Bearing | 66-75 Ford Bronco

Question 8

Will these work for a front axle from a 77 Ford F150 with a high pinion dana 44? To my understanding it is the same axle as the 78-79 Bronco but would like to verify. View answer

Answer posted 3 years ago | Dana 44 Axles + Spicer 760X U-joints | 4340 Chromoly | 78-79 Bronco, 68-79 F150

Question 9

Purchasing as option #2 or #3: does it come with the necessary mounting hardware? Does the stock hardware need to be reused? View answer

Answer posted 3 years ago | Lokar Billet Aluminum E-Brake Pedal Pad | 66-91 Bronco, 61-91 Ford Truck

Question 10

Will this rebuild kit also work with a stock pinion support that will be installed in a 35 spline carrier housing? View answer

Answer posted 3 years ago | Third Member Rebuild Kit | 35 spline, Daytona | LM104949/LM104911

Question 11

Does the constant velocity yoke in this kit come with the little spring? Is that spring absolutely necessary? I lost mine taking it apart. Do you sell just the spring? View answer

Answer posted 3 years ago | Driveshaft Rebuild Kit | U-Joints + CV Yoke | 66-77 Ford Bronco

Question 12

Is it possible to purchase the grille and tailgate and include them in the "Free Shipping" kit? ready to pull the trigger. View answer

Answer posted 3 years ago | Early Bronco Body Tub Kit w/Uncut Quarters | Freight Included

Question 13

Where does this harness allow for the computer to be mounted? View answer

Answer posted 3 years ago | WH Custom Fuel Injection Wiring Harness | 86-93 Ford 5.0L

Question 14

my 76 bronco manual shift on the column has this type of shift linkage retainer, looks like it was installed from the factory, does it also need the item# 8388 shift linkage retainer clip installed on the rod? View answer

Answer posted 3 years ago | Holley Performance Products > C4 Automatic Shift Linkage Retainer Bushing | 73-77 Bronco, 73-93 Ford Truck

Question 15

Hi,<br>Will this item work well w/ a T handled shifter? Or will I need a '66/other solid shaft? View answer

Answer posted 3 years ago | Transfer Case Shifter Knob | OE-Type | 1966 Ford Bronco

Question 16

Are the full body kits welded together and assembled View answer

Answer posted 3 years ago | SUPER MEGA Early Bronco Body Tub Kit w/Uncut Quarters & Bolt-On Parts

Question 17

Can you use this intake and keep your stock 2 barrel carb? Or does this require an upgrade to a 4 barrel? View answer

Answer posted 3 years ago | Edelbrock Performer Black Intake Manifold | Ford 260 289 302

Question 18

Do these hoses work on F 150 knuckle conversion brakes as well? View answer

Answer posted 3 years ago | Bilstein 5100 Shock - Eye/Eye, 26' Extended, 16' Compressed

Question 19

Does the rear bench come with seat belts? View answer

Answer posted 3 years ago | Caballo Fold & Tumble Rear Bench Seat | Black Pleated | 66-77 Ford Bronco

Question 20

Do you sell just the oil pickup tube? Or can you give me the brand and part #of this pickup tube? View answer

Answer posted 3 years ago | Engine Oil Pan Kit + Stainless Dip Stick & Tube | SBF 289 302 V8 | 66-77 Ford Bronco

Question 21

Are the lens real glass? View answer

Answer posted 3 years ago | H4 Headlights Kit + Night Lighter Harness | OE-Look | 66-78 Bronco, 48-78 Ford Truck

Question 22

Will the U-bolt plate work for a 73 f100 while using the original u bolts? View answer

Answer posted 3 years ago | Leaf Springs Kit | 4-inch Lift | 78-79 Bronco, 73-79 Ford F150 4WD

Question 23

Does both emblems come with this or do I need to order one for each side? View answer

Answer posted 3 years ago | 302 Engine Badge Emblem | Red Accent | 69-77 Bronco, 67-72 Ford Truck

Question 24

Will this work on a 1973 Ford Bronco? And what other parts would I need? View answer

Answer posted 3 years ago | Windshield Washer Solvent Pump | 68-70 Ford Bronco & Truck

Question 25

I did a shackle flip on my 68 Bronco resulting in a 3 lift, will it be ok to use your Wrap Trap with this arrangement? View answer

Answer posted 3 years ago | Fuel Tank Strap J-bolt | OE-Type | 66-77 Ford Bronco

Question 26

Do you have a fuel tank vent hose for a 77 ? View answer

Answer posted 3 years ago | Fuel Tank Vent Hose | Main or Auxiliary | 66-76 Ford Bronco

Question 27

Can I install this without removing the transfer case? I have a 1975, 302 w/auto. View answer

Answer posted 3 years ago | Dana 20 Twin Stick Transfer Case Shifter Kit | Stock J-Shift | 73-77 Ford Bronco

Question 28

will this fit my 1973 Bronco with 302 V-8 engine? View answer

Answer posted 3 years ago | Radiator Fan Shroud | OE-Type, Plastic | SBF V8 | 66-77 Ford Bronco

Question 29

With 2.5 in lift does it need longer brake lines steering components View answer

Answer posted 3 years ago | Early Bronco 2.5-inch Suspension Lift w/WH Nitro All Terrain Shocks | System 3

Question 30

Will this defroster duct work on a 1966 Bronco also? View answer

Answer posted 3 years ago | Defroster Duct | Heavy Duty | 68-77 Ford Bronco

Question 31

Do you have a stock steel hood with an extra raised steel center area on hood like the fiberglass hoods. View answer

Answer posted 3 years ago | Classic Instruments > Steel Hood | OE Quality | 66-77 Ford Bronco

Question 32

How hard is this to install, as I'm guessing the line has to be spliced, are there instructions? Also does the dash fuel selector not work after installation? View answer

Answer posted 3 years ago | Stainless Fuel Hose Kit | Dual Tank w/Under Seat Switch | 66-77 Ford Bronco

Question 33

Will these cables fit with your 5.5 suspension lift? Thanks! View answer

Answer posted 3 years ago | E-Brake Cables | Explorer Type Rear Disc Kit, PAIR | 66-77 Ford Bronco

Question 34

what are people doing for the gap created by the rear caps when wanting to put on a soft top or hard top. View answer

Answer posted 3 years ago | Armor-Geddon Rear Quarter Panel Guards | 66-77 Ford Bronco

Question 35

Does anyone make a soft top in brown? I know someone had one at one time? View answer

Answer posted 3 years ago | Red Paracord Grab Handles | Bolt-On, PAIR | 21-25 Ford Bronco

Question 36

On the 5.0 Serp radiator (item 5006) was the measurement from cap to outset of top passenger side hose connect? View answer

Answer posted 3 years ago | Ron Davis Aluminum Radiator | SBF 289 302 351W V8 | 66-77 Ford Bronco

Question 37

Does the new AX 15 transmission come with a warranty? View answer

Answer posted 3 years ago | AX15 Kit with Brand New Transmission For 66-72 Bronco T-Shift Dana 20

Question 38

do you sell just the hardware? View answer

Answer posted 3 years ago | Custom Door Straps for Speaker & Power Windows Wires | 66-77 Ford Bronco

Question 39

Sir,Will your front driver roll bar fit a 54 inch wide bronco 2? View answer

Answer posted 3 years ago | Early Bronco 1.5-inch Suspension Lift w/Bilstein 5100 Shocks | System 3

Question 40

Do the Jambits come in a set(driver/pass), and do they cover both for and aft jams? View answer

Answer posted 3 years ago | Jambits Smooth Door Jam Caps | Finished Look w/o Doors | 66-77 Ford Bronco

Question 41

What voltage is this set to? View answer

Answer posted 3 years ago | Precision Electronic Instrument Voltage Regulator | 66-77 Bronco, 57-66 Ford Truck

Question 42

Will these work well with the rear passenger seats? Do you have any additional pictures of the other hardware included with the seat belts? View answer

Answer posted 3 years ago | Derale Performance > Door Latch Rod | RH Passenger | Lock Knob/Latch | 68-77 Ford Bronco

Question 43

If this is to be shipped by truck freight, how can I get it, trucks can't get down my road? How much does it weigh? <br>Thank You,<br>David View answer

Answer posted 3 years ago | Custom Family Roll Cage | 8-point, Fully Welded | 66-77 Ford Bronco

Question 44

What ratio is this steering box? View answer

Answer posted 3 years ago | Power Steering Conversion Kit | Quick Ratio | 66-77 Ford Bronco

Question 45

Is this tank made with galvanized steel? View answer

Answer posted 3 years ago | Rear Main Fuel Tank Master Kit | OE-Type | 66-76 Ford Bronco

Question 46

what is the proper installation of this windshield hinge? industrial rivots? or tack weld? View answer

Answer posted 3 years ago | Windshield Frame Hinge | Stainless | 66-77 Ford Bronco

Question 47

Does this turn signal switch fit a tilt wheel or non tilt wheel? View answer

Answer posted 3 years ago | Cowl Side Extension Panel Kit | 4-piece | 66-77 Ford Bronco

Question 48

How are they different? Is it just that they don't come with the shock mount? If so, that is fine as I am installing extended radius arms that relocate the front shock to behind the axle. I don't want to grind the shock mounts off of my stock ones. Dana 44 is a Dana 44 right? View answer

Answer posted 3 years ago | Gear Shift Arm | 1st & Reverse | 66-75 Bronco, 65-72 Ford Truck

Question 49

Purchased a HI volume steering pump system 2074 with remote reservoir. The reservoir has dual return ports yet the installation diagram only shows a single return line connection to the box. I'm running a hydraulic assist, has been installed for at least 3-4 years, and all other lines are connected as shown. What is the second return port used for or supposed to be connected to? View answer

Answer posted 3 years ago | Lower Coil Spring Mounting Cup | 78-79 Bronco, 77-79 Ford Truck

Question 50

Hi I have a 77 IH scout, it has a gm column non tilt. Is there an adapter available that would work with this steering wheel? View answer

Answer posted 3 years ago | Mark 7 Woody Black Billet Steering Wheel | Slotted 3-spoke | 14-inch

Browse by Topic